The material handling technology area encompasses systems and equipment for handling coil, sheet, plate, profiles, tube and pipe, raw materials, and scrap. It also covers peripheral accessories such as C-hooks, clamps, die storage systems, hoists, lifters, and sheet stackers and destackers.
February 4, 2015
Modern forming technology has made kit-based part flow much easier. But when you’re dealing with a dynamically nested sheet, with kits of different parts, pieces can get lost in the mix. Fabricators can tackle this problem with intelligent nesting and part identification.
November 10, 2014
Three friends grew up in Sweden playing with LEGO®s and Erector sets. The creations they could make were endless, but their assembly method was pretty much standardized. Why, they asked, couldn’t a similar concept apply to material handling carts in a factory?
August 4, 2014
Every employee at Pentair operates under PIMS, or the Pentair Integrated Management System. PIMS encompasses everything from continuous improvement and hiring practices to safety and ergonomics. Concerning the last, the company instituted new material handling technology within a tightly run tank fabrication line in Delavan, Wis. The line has no WIP and, hence, little margin for error.
July 28, 2014
Upgrade transfer systems’ controls, drives, and bearings without complete replacement with a refurbishment. An appliance-maker had new rail connections, new wireless electrical connection methods for part tracking, electronic torque monitoring, and new kinetics drives installed as part of its press modernization program at 75 percent of the cost of new transfers.
July 10, 2014
BSS Industrial, a plumbing and heating products distributor, was accustomed to using slings affixed to its fork lifts to lift tube bundles from truck beds. The drawback was that on occasion the load would swing, creating a tipping risk for the lift truck. Lift truck manufacturer Combilift developed a truck with standard-length forks for placing and picking inventory, and a longer set of forks for lifting tube bundles from the delivery vehicle’s bed.
March 10, 2014
A conveyor system only works as well as its weakest link. What are those weak links, and how do you recognize their signs of wear? What are the most critical components for optimal operations? How do you maintain the equipment and when do you know when to call in the calvary? This article answers those questions.
October 9, 2013
The American Society of Mechanical Engineers has established compliance standards for the use of permanent and electric-rated lifting magnets and the operators of those magnets. Familiarizing shop floor personnel with these guidelines builds a solid foundation for keeping employees safe as they move sheet metal and plate.
August 1, 2013
Manufacturers have many green options in their choices of lift trucks, including low- or no-emissions, energy-efficient forklift technologies. Raymond, Toyota, Nissan, Hyster, Yale, Power Designers, Minit-Charger, and AeroVironment weigh in on how today’s lift trucks meet demands for lower emissions, higher energy efficiency, and CARB and EPA emissions standards.
April 16, 2012
When Tioga Pipe Supply Co. Inc. built a new facility in Easton, Penn., it leveraged its 60 years in business to design its new building. It planned the new facility, 150,000 sq. ft. under roof and 10 acres of outdoor storage area, around the use of side-loading lift trucks. The only drawback was occasional damage to the fork trucks' guide rollers, which Combilift eliminated when it designed a set of adjustable guide rollers specifically for Tioga.
October 20, 2011
Drill lines must be robust enough to properly support the aggressive speeds and feeds of modern tooling. At the same time, shop layout and material handling strategies must ensure no drill line sits idle for excessive periods, just waiting for that next piece of material.
February 1, 2011
A Midwestern stamper installed a new press with an unusually high drop from the passline of the press to the scrap removal conveyor. The stamper determined that a magnetic conveyor could handle the challenges presented.
July 13, 2010
In April 2010, more than 100 wordsmiths from 30 countries traveled from as far away as New Zealand and Australia to the picturesque hills of County Monaghan, northwest of Dublin, to visit Combilift, a forklift manufacturer that manufactures locally, but sells globally.