Stamping Products

Whether you're using a high-speed stamping press to make simple parts at breakneck speeds or doing something really tricky, like deep drawing a material that puts up a lot of resistance, the information in this technology area is sure to help. The articles, case studies, and press releases cover stamping presses, lubricants, and materials.

Filter Content

Coil manipulator facilitates transfer to cart

September 11, 2007

Green Valley Mfg. Inc. has introduced the Titan 2327, a 12,000-lb.-capacity coil manipulator that allows the operator to safely transfer palletized steel coils to a coil cart. The load deck rotates 90 degrees to invert the coil, and a cart is then positioned under the coil for extraction and...

Continue Reading

Data sheet details hydraulic press maintenance programs

September 11, 2007

A two-page data sheet from Schuler Inc. details the company's comprehensive maintenance programs for optimizing oil, power unit, and system component performance of hydraulic presses and systems.The data sheet explains how scheduled filter-exchange procedures can increase equipment service life,...

Continue Reading

Spray nozzle connector reduces downtime

August 7, 2007

Industrial Innovations Inc. has introduced the Kwik Spra Release multiconnection system, designed to minimize downtime during die change.The system allows users to leave a set of spray nozzles on the die to avoid repositioning them with every die change. One side of the connector stays with the...

Continue Reading

Die protection module has up to 32 sensor inputs

June 12, 2007

Cieco Inc. now offers up to 32 sensor inputs for the die protection module of the Automator II press controller, twice as many as previously supplied. Each sensor can be programmed individually.Each bank of eight sensors can be programmed to be global (apply to each job), eliminating repetitive...

Continue Reading

Hydraulic presses introduced

June 12, 2007

Greenerd Press & Machine Co. Inc. has introduced a series of hydraulic presses for hot and cold forging. Applications include automotive and truck, aerospace, agricultural, industrial, hardware and tools, and surgical equipment.Produced by Tianjin Tianduan Press Co. in China, the presses can be...

Continue Reading

Sheet metal hemming press requires no hydraulics, plant air

June 12, 2007

Hirotec America offers the E3™ sheet metal hemming press.Twin 20-HP electric motors power the machine's dual-crank drive units and can hem automotive closures without hydraulics or plant air. The electronically coupled dual-crank drive does not require mechanical interlocks, providing...

Continue Reading

Die protection module provides flexible sensor monitoring

May 8, 2007

Cieco Inc. has introduced a new product for its Automator II press controller. The die protection module for the controller now has up to 32 sensor inputs available, twice as many as previously offered, and provides users with flexible sensor monitoring capabilities.Each of the 32 sensors can be...

Continue Reading

Press offers alternative to fine blanking

May 8, 2007

LMC Inc. offers a series of blanking press systems based on adiabatic technology. According to the company, adiabatic blanking can produce parts from virtually any metal and tensile strength and has blanked material in hardness up to 50Rc.The LMC SIP-15B press blanks up to 1,000 parts per minute....

Continue Reading

Press line expanded

May 8, 2007

Greenerd Press & Machine Co. Inc. has expanded its compression molding press line with increased tonnage capabilities up to 10,000 tons and bed sizes exceeding 240 in. The line is suitable for various compression molding applications, from automotive to electrical components, house wares, and...

Continue Reading

Die lifter has up to 450 lbs. force on contact

May 8, 2007

Dadco's patent pending SL2.180 nitrogen gas spring two post lifter is the latest addition to the company's SL series. The new lifter has a 31.8 mm profile, stroke lengths from 25 mm to 125 mm, and force on contact up to 450 lbs.Ᾱone size larger than the SL2.090 that has a 25 mm profile and...

Continue Reading

Tooling systems available for Danobat punch presses

April 10, 2007

Danobat punch press users can select from a full range of high-performance Mate tooling systems to fit their punching requirements. Available systems include Mate Ultra TEC®, Mate Ultra XT™, Mate original style thick turret tooling, and the Mate Ultraform® forming tool...

Continue Reading

Hydraulic press provides precision press parallelism

April 10, 2007

Beckwood Press Co. has recently delivered a hydraulic press made specifically with two-axis active leveling for precision parallelism of the press. This 230 ton capacity press is being used to form radiator tanks for a construction industry manufacturer.The press was specifically engineered for the...

Continue Reading

Mechanical punch stripper cleanly strips workpiece

March 13, 2007

Moeller Mfg. Co.'s True Strip die-spring-actuated mechanical stripper for punches is designed to strip the workpiece to prolong tool life and avoid double hits or parts stacked in the die.The NAAMS specification-compliant device is compact, interchangeable, and fits directly on industry standard...

Continue Reading

Press-to-press transfer system designed for enhanced productivity

March 13, 2007

Rexcon Controls and Automation, a division of Electrex Co. Inc., has introduced Production Pro Line Supervisor and Vision De-Stacker, which comprise a press-to-press transfer system designed to reduce startup and downtime.The Production Pro Line supervisor enables the press line robots to determine...

Continue Reading

Twin-cylinder press brake designed for general-purpose fabricating

February 13, 2007

Piranha is demonstrating its Piranha Pro2 synchronous twin-cylinder press brake at Westec 2007. The brakes come in various sizes and tonnage choices and are capable of most general-purpose fabricating from precision thin-gauge to heavy-plate.Features include:Two vertically mounted hydraulic...

Continue Reading