Our Sites

5 considerations when replacing a hydraulic press with a servo press

Control, flexibility, speed, cost, and longevity are key considerations for stampers

Greenerd Press & Machine Co. hydraulic press

Hydraulic press designs are easily modified to fit an application, with designs ranging from 1 to 150 tons per sq. ft. Stamping large sheets of thin material on a hydraulic press may require only 5 tons per sq. ft. These four 400-ton hydraulic presses in a transfer line are sized for 8 tons per sq. ft., while the 1,000-ton hydraulic press at the right is sized for 110 tons per sq. ft. Image provided by Greenerd Press & Machine Co.

Those operating old hydraulic presses and deciding to upgrade to new equipment face a choice: Is it more advantageous to move to an improved version of the hydraulic press that has always worked, or convert to a servo mechanical (servo) press instead?

This is a more complicated decision than it seems at first. Much like choosing between a hydraulic press and a traditional mechanical press, there are a series of trade-offs. Critical attributes to consider when reviewing any press application are control, flexibility, speed, cost, and longevity.

Control

Process control has become more critical as designers and manufacturers push the limits of new and existing materials. Servo mechanical presses provide a wealth of information on power, speed, force, and position. The servomotors driving the machine provide much of this feedback, using the same data that adjusts speed and power continuously. These adjustments and sensors are what enable servo presses to match preprogrammed process curves well. Servo mechanical presses perform particularly well in applications with high reverse tonnage and materials with significant springback tendencies.

Advanced hydraulic presses use a network of sensors to achieve a similar goal. The force being applied is monitored in the pressurized fluid of each cylinder. Position and speed are measured directly with linear transducers that are accurate within 10 microns. This information is used to manipulate hydraulic valves that control the speed and force independently. The reliance on a fluid, instead of a mechanical connection, can lead to dampened corrections in force or speed with similarly dampened final accuracy. However, at steady forming rates, the difference in accuracy between hydraulic and servo may be only a fractional percent.

Flexibility

Hydraulic presses have long been the default choice for deep forming applications because of their ability to apply full force at any point in the stroke. This enables them to produce parts that would require a servo mechanical press at triple the capacity. Many servo mechanical presses lose 50% of their available tonnage just 1 inch above bottom dead center. The size selection process for a servo press generally mirrors that of a mechanical press, with special attention paid to the forming depth of all the products being manufactured.

Design flexibility of the press can also play a role in choosing the right technology. Servo mechanical presses typically are ordered with a high force per square foot of working area, generally 25 to 50 tons per sq. ft. Hydraulic press designs are easily modified to fit an application, with designs ranging from 1 to 150 tons per sq. ft. Stamping large sheets of thin material on a hydraulic press may require only 5 tons per sq. ft. Having a press that can match the tonnage requirements can improve production rates and reduce costs dramatically.

Speed

A hydraulic press can achieve speeds of more than 1 meter per second during a stroke. However, it requires idle time each cycle for the shifting of hydraulic valves, which generally limits the press speed to less than 30 strokes per minute (SPM).

A servo mechanical press’s slide speeds typically are below 0.5 m/s. However, they can improve mechanical press cycle times by increasing speeds outside the working portion of the stroke. Within a stroke, the servomotors can achieve very high acceleration and can restrike a part within a tenth of a second.

The ability of both press systems to adjust speed accurately throughout the stroke—especially slowing at material penetration—results in longer die life and superior stamped products. This may be even more beneficial than reaching top speeds.

In large stampings, multiple complex geometries can be forming at varying points throughout the stroke. Adjusting the slide speed accurately can help control strain rates in the material. The fixed speed of a less advanced hydraulic press or the one-size-fits-all sinusoidal motion of a traditional mechanical press can require complex tooling and generate high scrap rates in these large components. However, advanced hydraulic controls and servomotors can provide a wider range of speed and force, opening up opportunities for increases in productivity and design freedom.

Greenerd Press & Machine Co. hydraulic press

The right choice of technology for a press application will vary and should be carefully considered with each new project. Image provided by Greenerd Press & Machine Co.

Cost

Servo mechanical press prices have been decreasing as the number of machines being produced has been rising. Generally, though, servo presses still have a higher initial price compared to hydraulic presses, and this cost differential increases at higher capacities.

The servomotor and drive systems are the main reason for these high costs. Hydraulic press pumps and cylinders have a more modest cost, and the price increases that occur as systems grow larger are more moderate too. The total cost of ownership will tend to favor a hydraulic press in many applications, while the lower operating costs of a servo mechanical press may result in cost savings.

Longevity

While many traditional hydraulic and mechanical presses are in operation today with more years of service than any employee, the same cannot be said of servo presses. The long-term cost of ownership of a servo mechanical press in various applications is still being evaluated. Regular maintenance items in a servo press are lower as a result of lower impact forces and fewer components. But the components can be specialized and expensive. A hydraulic press has more points of failure to contend with, yet repairs are generally quick and the parts readily available.

Proper care of the equipment with correct work sizing and regular preventive maintenance will significantly improve outcomes, regardless of press type.

Careful Consideration

Hydraulic presses can adapt to produce almost any product cost-effectively and often are the only option for systems with a high force demand early in the stroke. Servo presses represent an evolution in mechanical press technology, opening new opportunities for manufacturers with difficult processes or materials. While they increase the flexibility of the underlying mechanical press design, they still carry many of the same limitations.

Ultimately, the right choice of technology for a press application will vary and should be carefully considered with each new project.

Mike Josefiak is a design engineer for Greenerd Press & Machine Co., 41 Crown St., Nashua, NH 03061, 603-889-4101, greenerd.com.

Greenerd Press & Machine Co. hydraulic press

Hydraulic presses can adapt to produce almost any product cost-effectively and often are the only option for systems with a high force demand early in the stroke. Image provided by Greenerd Press & Machine Co.