Our Sites

Die Science: Friction and heat in metal stamping

Taking a look beyond the press guidelines for applications and lubricants

Hydraulic press stamping machine for forming metal sheet, Industrial metalwork manufacturing

Getty Images

When I was in a metal stamping facility recently, one of the tooling engineers wanted to show me a deep-drawing process that he said defied all that he had learned about metal forming basics. He even commented that a lot of the information he acquired was from articles I’d written for STAMPING Journal. He explained that the die would perform well only if lubrication on the blank was very light and the press ram was moving very quickly. This was quite perplexing to him, as his own personal experience with other drawing operations and the information that he learned from his research typically indicated that more lubricant and slower ram speeds are required for successful deep drawing. How could this be?

He then went on to prove what he’d told me about this tool. Sure enough, when he added more lube, the part would split; when he slowed the ram speed down, the part would split.

Guidelines Versus Rules

If you’ve been reading my articles over the last 20 years, you might have noticed that I use a lot of “weasel phrases”: I usually preface my statements with generally speaking or in most cases or by far. That’s not because I lack confidence in my statements, but because I’ve learned that absolutes are rare in sheet metal stamping. Sure, we adhere to guidelines and basic foundational principles, but they are only guidelines, not absolute rules. In fact, the only absolute rule is “There are no absolute rules.”

General guidelines serve as a foundation for most but not all metal forming and cutting operations. You must comprehensively understand all the variables to make a good data-based decision, not just rely on the guidelines.

A Basic Guideline: Slower Is Better for Deep Drawing

In my articles and conferences, I like to teach attendees and readers to visualize the material they are forming, stretching, or cutting as Silly Putty. One of the interesting behaviors of this toy compound is that if you pull it quickly, it fractures, but if you pull it slowly, it stretches.

Most materials being deep drawn or stretched behave in a similar fashion. This explains why complex deep-drawn parts such as sinks, bathtubs, and wheelbarrows usually are made in slower hydraulic presses. The excessive speed of a typical crank-drive mechanical press often causes splitting because the material needs time to flow.

The point at which the punch contacts the material during deep drawing is critical. At this point in the press stroke, the material is forced to go from zero velocity to a value equivalent to the ram speed—in zero time. If there is not enough time to initiate the metal flow, the result is excessive stretch and potential splitting.

Metal cutting, on the other hand, usually is performed quickly. Think of metal cutting as metal forming to failure. In metal cutting, you want the material to fail, so excessive speeds are desirable.

The Game-Changers: Heat and Friction

Heat and friction are generated in all metal cutting and forming operations. The amount generated is a product of many variables, including the material type and thickness, the forming geometry, the tool steel type, the friction between the sheet material and the die, the forming velocity, the forming severity of the feature, and the behavior of the lubricant.

Heat. Heat can be a friend or a foe in a stamping process. An increase in heat can improve the ductility and performance of the material you are forming. This is why some dies need to warm up to perform adequately. When you want to bend a large piece of angle iron, what do you do? You heat it up, and it bends easily.

FIGURE 1. Many lubricant additives reduce the coefficient of friction dramatically when they are subjected to high temperatures, while others work better at lower temperatures.

This same principle applies to metal forming. In fact, it’s the basis for the hot stamping process. However, in some instances, excessive heat can cause tool steel sections to get damaged and lubricants to perform inadequately or burn off. Subsequently, die damage such as galling can occur, which can contribute to splitting and premature tool failure.

Friction. Lubricants contain additives that react to heat. Many additives reduce the coefficient of friction dramatically when they are subjected to high temperatures, while others work better at lower temperatures (see Figure 1). Lubricants containing high-temperature additives, like sulfur, perform best when the friction and heat generated are high. But they don’t perform well at lower temperatures, so if the operating temperature of the sulfur additive is not reached, the friction in the die will be high. This equates to low metal flow values, which leads to more stretch, which leads to potential failure.

The Mystery Part

Although I never took the time to prove it out, I suspect that the tooling engineer’s part didn’t split at higher forming speeds because of four contributing factors:

  1. The lubricant contained high-temperature additives, which lowered the coefficient of friction at high heat values.
  2. The increased speed caused greater friction, which resulted in higher heat, causing the additives to decrease friction and increase the amount of material flowing into the die.
  3. The lower volume of lubricant being applied contributed to increased friction, which increased the amount of heat in the die.
  4. The heat and friction in the metal caused by higher forming speeds, the lack of low-temperature additives, and the lower lubricant amounts elevated the ductility of the material.

Because of the numerous variables in sheet metal forming and cutting, we have guidelines rather than absolutes. That’s why it’s important to have a comprehensive understanding of the physics behind metal forming and cutting instead of relying on the tribal knowledge passed down from generation to generation.

About the Author
Dieology LLC

Art Hedrick

Contributing Writer

10855 Simpson Drive West Private

Greenville, MI 48838

616-894-6855

Author of the "Die Science" column in STAMPING Journal®, Art also has written technical articles on stamping die design and build for a number of trade publications. A recipient of many training awards, he is active in metal stamping training and consulting worldwide.