Our Sites

Dissecting 7 common stick welding problems

How welders can troubleshoot SMAW problems and prevent mistakes

Stick welding

Using the proper technique and following some best practices can help improve your SMAW results.

Using proper technique and following some best practices can help you improve your shielded metal arc welding (SMAW) skills. But no matter how meticulous you are, you can still run into problems on occasion.

Knowing how to quickly identify and troubleshoot common SMAW problems can reduce unnecessary downtime, which is particularly important since the process is already relatively slow compared to wire processes. Any time saved can help contribute to better productivity and less frustration.

Consider these seven common SMAW issues and their solutions to help along the way.

Problem No. 1: Spatter

Two of the most common causes of weld spatter are welding with an arc length that is too long and welding on a dirty surface. An arc length that is too long can cause a ball to form on the end of the electrode. Spatter happens when that ball detaches and drops into the puddle. Also, failing to clean the base material can result in weld contamination that also leads to spatter.

Spatter also can result from a welding current that is set too high; arc blow; or if you weld with a wet, unclean, or damaged electrode.

If you’re frequently dealing with spatter, try adjusting your weld current and maintaining the correct arc length. Be sure to clean the base material before you weld, and follow the filler metal manufacturer’s recommended oven storage and reconditioning to prevent the electrode from picking up moisture.

Problem No. 2: Porosity

Starting the weld with unclean base material is also a common cause of porosity. Oil, grease, moisture, rust, or mill scale on the metal can contaminate the weld with impurities. Properly cleaning the base material before welding and storing welding electrodes properly can help prevent this.

Porosity also can be caused by excessively long or short arc lengths, so it’s important to maintain the proper arc length. An arc that’s too long means you’re not getting to a point where the shielding atmosphere is protecting the weld. The recommended arc length varies by electrode diameter. Weld data sheets often note the recommended lengths — typically no more than the diameter of the core wire.

In addition, a welding current that is too high causes the weld pool to freeze before the gas can escape, resulting in porosity. Using a travel speed that’s too fast can cause similar problems because you’re essentially outrunning your gas coverage. Adjust your speed accordingly.

Problem No. 3: Lack of Fusion or Poor Penetration

Lack of fusion occurs when there is no fusion between the weld metal and the base material surface. Poor penetration is similar in that the weld bead doesn’t fully penetrate the entire thickness of the base material or fully penetrate into the weld toe.

Both of these can occur when the welding current is set too low and doesn’t provide enough amperage to actually penetrate the joint, or when the joint is designed poorly or when the joint preparation is faulty.

Lack of fusion or poor penetration happens when your travel speed is too fast, if your electrode is too large for the joint, if you aren’t using the correct electrode type, or if your electrode angle is incorrect.

To remedy challenges with both lack of fusion and poor penetration, reduce your travel speed and increase the welding current. Also, be sure that the weld design allows electrode accessibility to all surfaces within the joint. Using a smaller-diameter electrode also can help.

Problem No. 4: Undercut

Undercut—when the joint is not properly filled in—results in a groove or eroded section.

Using a welding current that’s too high or travel speed that is too fast is a common cause of undercut. A too-fast travel speed means you’re not staying in position long enough to properly fill the joint. Arc blow and faulty electrode manipulation also can result in undercut.

To avoid this, be sure to pause at each side of the weld bead when using a weaving technique. Also, use correct electrode angles, reduce travel speed, and use the proper welding current for the electrode size and welding position.

Problem No. 5: Overlapping or Overwelding

Overlap occurs when the molten weld metal runs over the surface of the base material and cools without fusing. This typically is caused by slow travel speeds and staying too long in the puddle, resulting in more weld metal than necessary filling the joint. An incorrect electrode angle or using an electrode that is too large can cause overlapping too.

To prevent this, increase your travel speed and use proper work angles as recommended by the filler metal manufacturer. Also, use a small electrode to prevent adding too much molten metal into the joint.

Problem No. 6: Arc Blow

Magnetic arc blow happens when there is an unbalanced magnetic field during welding or there is an excessive magnetism in either the part or the fixture. This can happen in an electric system when it magnetizes itself.

Arc blow can happen when welding toward or away from the ground clamp. The closer you get to the ground, the more the arc will wander. This is called backward arc blow. Forward arc blow occurs in the presence of the unbalanced magnetic field when welding away from the ground.

To prevent arc blow, change the location of the ground connection on the workpiece. It also helps to reduce the welding current and arc length and use alternating current.

Problem No. 7: Trouble Striking An Arc

If you are just learning SMAW, it can be common to face problems with the electrode sticking to the workpiece. When striking the arc, be sure to strike the workpiece and lift the electrode at the same time.

Certain electrodes may seem easier to strike than others. For example, E7018 electrodes seem to stick more than other types, while deeper-penetrating electrodes such as E6010 and E6013 typically don’t stick as much because they have more drive to their arc.

Take care when using low-hydrogen E7018 electrodes. They should be oven-stored to prevent moisture pickup. Moisture absorbed in these electrodes will increase hydrogen in the weld and result in cracking.

About the Author

Kim Francis

Application Specialist

101 Trade Square East

Troy, 45373

(937)-332-4000