Senior Company Trainer
- FMA
- The Fabricator
- FABTECH
- Canadian Metalworking
Categories
- Additive Manufacturing
- Aluminum Welding
- Arc Welding
- Assembly and Joining
- Automation and Robotics
- Bending and Forming
- Consumables
- Cutting and Weld Prep
- Electric Vehicles
- En Español
- Finishing
- Hydroforming
- Laser Cutting
- Laser Welding
- Machining
- Manufacturing Software
- Materials Handling
- Metals/Materials
- Oxyfuel Cutting
- Plasma Cutting
- Power Tools
- Punching and Other Holemaking
- Roll Forming
- Safety
- Sawing
- Shearing
- Shop Management
- Testing and Measuring
- Tube and Pipe Fabrication
- Tube and Pipe Production
- Waterjet Cutting
Industry Directory
Webcasts
Podcasts
FAB 40
Advertise
Subscribe
Account Login
Search
How to demagnetize metal pipe for welding
- By Jim Mosman, AWS, CWI/CWE
- Updated December 7, 2023
- March 26, 2019
- Article
- Arc Welding
Q: We discovered that some pipe that arrived on the construction site would not take a weld because it was magnetized. What is a good method to demagnetize the pipe so we can weld it?
A: This is a fairly common problem that occurs when lengths of pipe get banged together during the shipping process. Magnetism results in magnetic arc blow, a phenomenon that occurs during direct current (DC) welding, where the arc pulls to one side of the weld joint during the root pass. This deviation of the arc often can be severe and cause weld defects that will need to be repaired.
You have a few options if you suspect your material is magnetized. You could remove the magnetism completely, but that would require expensive equipment. You could also determine the extent of the magnetic pull with a gauss gauge before you place a demagnetizer coil around the pipe, but this type of equipment may not always be available.
One common method that I have used on pipelines in the oil and gas industry is to create a magnetic coil with the work lead. I wrap the lead around the pipe three to six times, about half the pipe diameter away from the weld groove on the opposite side from the direction of the arc blow pull. Then I deposit several ¾- to 1-in. tack welds around the weld joint. Using a current in the lower range of what is suggested, I deposit a root pass with a short arc length based on the size and type of my electrode. If I’m still experiencing arc blow, I then try to wrap the work lead in the opposite direction.
Finally, since arc blow occurs during DC welding, try switching to alternating current (AC) to deposit the initial weld bead. Then switch back to DC for the remainder of the weld joint.
Whatever method you use, be sure to pay close attention to the weld puddle, maintain a short arc length, and remove all slag deposits after each bead. You are the first line of inspection and should be aware of the quality of your work.
About the Author
Jim Mosman, AWS, CWI/CWE
Lincoln Electric Education Division
About the Publication
subscribe now
The Welder, formerly known as Practical Welding Today, is a showcase of the real people who make the products we use and work with every day. This magazine has served the welding community in North America well for more than 20 years.
start your free subscription- Stay connected from anywhere
Easily access valuable industry resources now with full access to the digital edition of The Fabricator.
Easily access valuable industry resources now with full access to the digital edition of The Welder.
Easily access valuable industry resources now with full access to the digital edition of The Tube and Pipe Journal.
Easily access valuable industry resources now with full access to the digital edition of The Fabricator en Español.
- Podcasting
- Podcast:
- The Fabricator Podcast
- Published:
- 03/26/2024
- Running Time:
- 67:51
This week on The Fabricator Podcast, Jason Becker, host of the Arc Junkies Podcast and owner of Underground...
- Trending Articles
A welding instructor’s career path to working with metal
The importance of welding procedure specification (WPS)
Keys to adopting welding automation successfully
Urban Steel Rockstars festival will highlight welding and steel industry
Sensors use AI to assist robotic weld grinding
- Industry Events
Coil Processing Workshop & Tours
- April 2 - 3, 2024
- Corpus Christi, TX
GOLF4MFG South
- April 15, 2024
- Charlotte, NC
16th Annual Safety Conference
- April 30 - May 1, 2024
- Elgin,
Pipe and Tube Conference
- May 21 - 22, 2024
- Omaha, NE
World-Class Roll Forming Workshop
- June 5 - 6, 2024
- Louisville, KY