- FMA
- The Fabricator
- FABTECH
- Canadian Metalworking
Categories
- Additive Manufacturing
- Aluminum Welding
- Arc Welding
- Assembly and Joining
- Automation and Robotics
- Bending and Forming
- Consumables
- Cutting and Weld Prep
- Electric Vehicles
- En Español
- Finishing
- Hydroforming
- Laser Cutting
- Laser Welding
- Machining
- Manufacturing Software
- Materials Handling
- Metals/Materials
- Oxyfuel Cutting
- Plasma Cutting
- Power Tools
- Punching and Other Holemaking
- Roll Forming
- Safety
- Sawing
- Shearing
- Shop Management
- Testing and Measuring
- Tube and Pipe Fabrication
- Tube and Pipe Production
- Waterjet Cutting
Industry Directory
Webcasts
Podcasts
FAB 40
Advertise
Subscribe
Account Login
Search
Arc Welding 101: Sorting out SAW
- By Paul Cameron
- October 8, 2014
- Article
- Arc Welding
Q: What is the procedure qualification test for manufacturing pipe using submerged arc welding?
Sandesh P.
A: Pipe is manufactured by one of these four methods: electric resistance welding (ERW)/high-frequency induction (HFI) welding, seamless (plug/mandrel mill and extrusion), spiral welding, and longitudinal welding. Spiral and longitudinal welds typically are made by the submerged arc welding (SAW) process.
Ends of a formed section of plate, referred to as skelp, are brought together to form a butt joint. When pipes exceed 36 inches in diameter, two sections of skelp are brought together and joined with two butt joints 180 degrees to each other. These sections are typically 40 feet long.
The welding process consists of one or more electrodes (most likely three) under a blanket of granular flux. The electrodes can be AC, DC, or a combination of the two.
Procedure qualification would require running a test sample in the flat position (1G) on like material with a wall thickness of either 3/8 or 1 in., depending on the wall thickness of the pipe being manufactured.
The completed test sample needs to be visually acceptable; nondestructively tested, usually by radiograph; destructively tested through reduced section testing (a minimum of two specimens); and the root, face, or side bend-tested (minimum four specimens). Depending on the specific code requirements, the test sample may also require Charpy V-notch testing.
All these test types—visual, nondestructive, and destructive—must be found acceptable, and the manufacturing process needs to duplicate the testing process within acceptable tolerances.
The SAW process is used because of its efficiency, high deposition rates, deep penetration, and overall clean appearance. The specifics of the SAW process differ from producer to producer and with material composition and thickness, and are usually a producer’s closely guarded secret.
To research SAW in detail, refer to The Procedure Handbook of Arc Welding, 14th edition. It is available from The Lincoln Electric Company.
About the Author
Paul Cameron
Braun Intertec
4210 Highway 14 East
Rochester, MN 55904
About the Publication
subscribe now
The Welder, formerly known as Practical Welding Today, is a showcase of the real people who make the products we use and work with every day. This magazine has served the welding community in North America well for more than 20 years.
start your free subscription- Stay connected from anywhere
Easily access valuable industry resources now with full access to the digital edition of The Fabricator.
Easily access valuable industry resources now with full access to the digital edition of The Welder.
Easily access valuable industry resources now with full access to the digital edition of The Tube and Pipe Journal.
Easily access valuable industry resources now with full access to the digital edition of The Fabricator en Español.
- Podcasting
- Podcast:
- The Fabricator Podcast
- Published:
- 04/16/2024
- Running Time:
- 63:29
In this episode of The Fabricator Podcast, Caleb Chamberlain, co-founder and CEO of OSH Cut, discusses his company’s...
- Trending Articles
Sheffield Forgemasters makes global leap in welding technology
ESAB unveils Texas facility renovation
Engine-driven welding machines include integrated air compressors
How welders can stay safe during grinding
The impact of sine and square waves in aluminum AC welding, Part I
- Industry Events
16th Annual Safety Conference
- April 30 - May 1, 2024
- Elgin,
Pipe and Tube Conference
- May 21 - 22, 2024
- Omaha, NE
World-Class Roll Forming Workshop
- June 5 - 6, 2024
- Louisville, KY
Advanced Laser Application Workshop
- June 25 - 27, 2024
- Novi, MI