Professor Emeritus and Director - Center for Precision Forming
- FMA
- The Fabricator
- FABTECH
- Canadian Metalworking
Categories
- Additive Manufacturing
- Aluminum Welding
- Arc Welding
- Assembly and Joining
- Automation and Robotics
- Bending and Forming
- Consumables
- Cutting and Weld Prep
- Electric Vehicles
- En Español
- Finishing
- Hydroforming
- Laser Cutting
- Laser Welding
- Machining
- Manufacturing Software
- Materials Handling
- Metals/Materials
- Oxyfuel Cutting
- Plasma Cutting
- Power Tools
- Punching and Other Holemaking
- Roll Forming
- Safety
- Sawing
- Shearing
- Shop Management
- Testing and Measuring
- Tube and Pipe Fabrication
- Tube and Pipe Production
- Waterjet Cutting
Industry Directory
Webcasts
Podcasts
FAB 40
Advertise
Subscribe
Account Login
Search
Dissecting defects - Part III
Stamping process control
- By Taylan Altan, Ph.D.
- December 11, 2007
- Article
- Bending and Forming
Real-time Process Control
Variations in incoming sheet material quality, tool temperatures, press and tool deflection, and lubricant performance result in deviations in formed part quality. Part failures interrupt production and can cause tool damage; thus, in addition to the initial tryout period, adjustments are routinely made during production to maintain good formed part quality.
Real-time or online monitoring of the stamping process has become essential to improve stamped part quality and prevent interruptions in production. Many types of sensors are used in production to monitor such process conditions as press tonnage, press slide movement, tool condition, tool alignment, lubricant quantity, and sheet material flow.1
Optical Measuring Technologies
Optical measuring technologies have found increased application in the sheet metal forming industry. Figure 1 shows a commercially available optical system used to obtain the deformation of a stamped component.
Before deformation, the sheet is marked with a grid of dots, using chemical etching, laser marking, or other marking techniques. For measurement purposes, one or two scale bars and some coded markers are placed directly on the part or near it. A high-resolution digital camera then is used to take shots from different viewing directions.
After images are taken, the optical system defines in each image the exact centerpoint of all marked dots. Then the images are virtually assembled with photogrammetric techniques to represent the object as a virtual 3-D model. From this virtual assembly, the center of each marked dot on the object is defined in true 3-D coordinates.
The calculated 3-D points define the exact form of the stamped sheet part. The deformation (stresses and strains) introduced by the stamping process can be calculated easily from the local distortion of the regular grid pattern on the sheet surface.2
In stamping, the main applications of optical technology are:
- Digitization of prototype sheet parts and tools.
- Forming analysis of metal sheets and tubes.
- Determination of material properties.
Depending on the application, specialized commercial software is available to process the digital images. The use of this technology also can verify and optimize numerical simulation programs for forming processes. These measuring technologies are being used increasingly for automated inspection tasks by integration of automatic vision systems into the process. For example, these cameras can be located at the exit of the stamping press to take real-time pictures of the deformed part.
In-process Control of the Deep-Drawing Process
Figure 2 shows an example of real-time monitoring of material flow in a deep-drawing process through the use of position sensors. The flange insertion position sensor (left) consists of a thin metal tongue that touches the outer edge of the blank sheet at the gap between the die and blank holder during the entire process.
This sensor, and others that have different designs but similar functions, detects the movement of the flange during deep drawing. Measured flange movement or draw-in versus the drawing depth can indicate the part quality. Any deviation from a prescribed tolerance range can be used to describe the potential failure.
The right side of Figure 2 shows a similar concept used for real-time monitoring of wrinkles in a deep-drawing process. Two position sensors are installed, one in the die and one in the blank holder. When a wrinkle occurs, the gap between the die and blank holder increases. Thus, the two sensors can detect and record the height of the wrinkle.
With real-time monitoring of the wrinkle height and flange movement, the blank holder force can be increased or decreased through a closed-loop control system.3 Using this principle, researchers at the University of Hanover, Germany, designed and built a closed-loop control system for deep drawing of rectangular pans using a multipoint cushion system. Contact-free optical sensors were placed at multiple locations around the flange periphery to detect material flow (wrinkles and flange movement). The developed closed-loop system was tested by varying the initial blank shape, and it gave good results.4
This column was prepared by Ajay D. Yadav, graduate research associate, of the Center for Precision Forming (CPF), The Ohio State University, for Taylan Altan, professor and director of the CPF, 339 Baker Systems, 1971 Neil Ave., Columbus, OH 43210-1271, 614-292-9267, www.cpforming.org. The CPF conducts research and development; educates students; and organizes workshops, tutorials, and conferences for the industry in stamping, tube hydroforming, forging, and machining.
Notes
- Doege et al., Metal Forming, Sensors in Manufacturing, ed. H.K. Tonshoff and I. Inasaki (New York: Wiley-VCH, 2001), pp. 172-190.
- K. Galanulis, "Optical Measuring Technologies in Sheet Metal Processing," SHEET METAL 2005, Advanced Materials Research, Vols. 6-8, Gesellschaft für Optische Messtechnik mbH, pp. 19-34.
- Doege et al., Metal Forming, Sensors in Manufacturing.
- Behrens et al., "Closed-Loop-Control of Deep-Drawing Processes by Means of Contact-free Measurement of the Material Flow," Annals of the German Academic Society for Production Engineering, 2005, XII/1, p. 45.
About the Author
Taylan Altan, Ph.D.
subscribe now
The Fabricator is North America's leading magazine for the metal forming and fabricating industry. The magazine delivers the news, technical articles, and case histories that enable fabricators to do their jobs more efficiently. The Fabricator has served the industry since 1970.
start your free subscription- Stay connected from anywhere
Easily access valuable industry resources now with full access to the digital edition of The Fabricator.
Easily access valuable industry resources now with full access to the digital edition of The Welder.
Easily access valuable industry resources now with full access to the digital edition of The Tube and Pipe Journal.
Easily access valuable industry resources now with full access to the digital edition of The Fabricator en Español.
- Podcasting
- Podcast:
- The Fabricator Podcast
- Published:
- 04/30/2024
- Running Time:
- 53:00
Seth Feldman of Iowa-based Wertzbaugher Services joins The Fabricator Podcast to offer his take as a Gen Zer...
- Industry Events
Pipe and Tube Conference
- May 21 - 22, 2024
- Omaha, NE
World-Class Roll Forming Workshop
- June 5 - 6, 2024
- Louisville, KY
Advanced Laser Application Workshop
- June 25 - 27, 2024
- Novi, MI
Precision Press Brake Certificate Course
- July 31 - August 1, 2024
- Elgin,