President
- FMA
- The Fabricator
- FABTECH
- Canadian Metalworking
Categories
- Additive Manufacturing
- Aluminum Welding
- Arc Welding
- Assembly and Joining
- Automation and Robotics
- Bending and Forming
- Consumables
- Cutting and Weld Prep
- Electric Vehicles
- En Español
- Finishing
- Hydroforming
- Laser Cutting
- Laser Welding
- Machining
- Manufacturing Software
- Materials Handling
- Metals/Materials
- Oxyfuel Cutting
- Plasma Cutting
- Power Tools
- Punching and Other Holemaking
- Roll Forming
- Safety
- Sawing
- Shearing
- Shop Management
- Testing and Measuring
- Tube and Pipe Fabrication
- Tube and Pipe Production
- Waterjet Cutting
Industry Directory
Webcasts
Podcasts
FAB 40
Advertise
Subscribe
Account Login
Search
Aluminum Workshop: Fine-line lack of fusion and its causes
- By Frank Armao
- November 16, 2015
- Article
- Aluminum Welding
Q: I recently fabricated a large component from 1-in.-thick 5083 aluminum. The customer required it to be radiographed. His inspector failed one of the radiographs because of a lack of fusion (LOF) discontinuity. I looked at the radiograph and I can’t see any discontinuity. Could the inspector be correct, or should I raise this to the next level?
A: Sad to say, the inspector is probably correct. Aluminum welds are somewhat prone to what are called fine-line LOF discontinuities. The term fine line refers to where the weld lies firmly against the joint preparation or underlying weld pass without melting into it and fusing.
This discontinuity can be extremely difficult to detect, even with radiography (see Figure 1). It is very subtle, but if you look carefully at the left fusion line of the weld, near the top in the pass before the cap passes, the straight fusion line at a 45-degree angle is actually an LOF. I think you can see why such discontinuities are hard to detect.
We can attribute the cause to a few possibilities. The aluminum might not burn through if excess oxide exists on the joint preparation before welding or on the weld bead before you make the next pass. Be sure to clean the area or the previous pass with a wire brush to remove the oxide before welding.
Next, it’s possible that your welding parameters are set too cold to melt the surrounding material. The weld in Figure 1 shows that the inside welds and the outside welds are not aligned. The welder just held the torch too far to one side and never really fused to the left-side weld preparation.
There is a practical consideration here in qualifying aluminum welders. Most codes allow the fabricator to qualify welders using either bend tests or radiography. Most welders prefer to take bend tests because they think the bend test is easier to pass. It isn’t. As you have seen here, radiography can easily miss LOF discontinuities. On the other hand, if you bend test an aluminum weld that contains any LOF, the discontinuity will pop right open.
About the Author
Frank Armao
Aluminum Consulting Inc.
440-479-0239
About the Publication
Related Companies
subscribe now
The Welder, formerly known as Practical Welding Today, is a showcase of the real people who make the products we use and work with every day. This magazine has served the welding community in North America well for more than 20 years.
start your free subscription- Stay connected from anywhere
Easily access valuable industry resources now with full access to the digital edition of The Fabricator.
Easily access valuable industry resources now with full access to the digital edition of The Welder.
Easily access valuable industry resources now with full access to the digital edition of The Tube and Pipe Journal.
Easily access valuable industry resources now with full access to the digital edition of The Fabricator en Español.
- Podcasting
- Podcast:
- The Fabricator Podcast
- Published:
- 04/30/2024
- Running Time:
- 53:00
Seth Feldman of Iowa-based Wertzbaugher Services joins The Fabricator Podcast to offer his take as a Gen Zer...
- Trending Articles
Aluminum MIG wires offer smooth feeding, reduced tangling
The role of flux in submerged arc welding performance
Three ESAB welding machines win Red Dot Awards for product design
Power source added to cobot welding system for simplified automation
Connecticut students compete in Maritime Welding Competition
- Industry Events
Pipe and Tube Conference
- May 21 - 22, 2024
- Omaha, NE
World-Class Roll Forming Workshop
- June 5 - 6, 2024
- Louisville, KY
Advanced Laser Application Workshop
- June 25 - 27, 2024
- Novi, MI
Precision Press Brake Certificate Course
- July 31 - August 1, 2024
- Elgin,